Alkali-Activated Materials Doped with ZnO: Physicomechanical and Antibacterial Properties.

The requirements related to reducing the carbon footprint of cement production have directed the attention of researchers to the use of waste materials such as blast-furnace slag or fly ashes, either as a partial replacement for cement clinker or in the form of new alternative binders. This paper presents alkali-activated materials (AAMs) based on blast-furnace slag partially replaced with fly ash, metakaolin, or zeolite, activated with water glass or water glass with a small amount of water, and doped with zinc oxide. The mortars were tested for flow, hydration heat, mechanical strength, microstructure, and antimicrobial activity. The obtained test results indicate the benefits of adding water, affecting the fluidity and generating a less porous microstructure; however, the tested hydration heat, strength, and antibacterial properties are related to more favorable properties in AAMs produced on water glass alone.

Synthesis and Characterization of Eco-Efficient Alkali-Activated Composites with Self-Cleaning Properties for Sustainable Construction.

In this research, we aimed to design an eco-efficient composite based on alkali-activated materials (AAMs) with self-cleaning properties for sustainable construction. Significant emphasis was placed on determining the role of the type of precursor, the amount of sodium silicate, and the addition of titanium dioxide on the rheological and mechanical properties of AAMs. An important aspect of the research was the modification of AAM with titanium dioxide to obtain the self-cleaning properties. Titanium dioxide, thanks to its photocatalytic properties, enables the reduction of organic pollutants and nitrogen oxides in the urban atmosphere and promotes the cleaning of material surfaces. Blast furnace slag (BFS) was used as the source material, which was then substituted in subsequent formulations with metakaolinite at 50% and fly ash and zeolite at 30%. The best-activated AAMs, in which blast furnace slag and its mixture with metakaolinite were used as precursors, achieved compressive strengths of 50 MPa. BFS mixtures with pozzolans were more difficult to polymerize, although their final strengths were still relatively high, in the range of 33-37 MPa. Adding titanium dioxide (T) improved the final strengths and slightly lowered the heat of hydration and spreading of the AAM mortars. The best self-cleaning properties were achieved with composites that comprised a mixture of blast furnace slag, fly ash, and 2% titanium dioxide.

Antimicrobial action and chemical and physical properties of CuO-doped engineered cementitious composites.

CuO nanoparticles (NPs) were added to cement matrices in quantities of 0.25, 0.50 and 1.00 wt% to inhibit the growth of Gram-positive (Bacillus cereus, Staphylococcus aureus) and Gram-negative (Pseudomonas aeruginosa, Escherichia coli) bacteria. It was shown that CuO NPs, in all tested concentrations, improved the antibacterial properties of the cement matrix. Nevertheless, the best mechanical, structural and durability properties were obtained for cement composites doped with CuO NPs at 0.25 wt%. Larger amounts of NPs caused a decrease in all parameters relative to the reference mortar, which may be the result of a slight change in the porosity of the composite microstructure. For 0.50 wt% CuO NPs, a slight increase in the volume of micropores in the cement matrix was observed, and an increased number of larger pores was confirmed by non-invasive computed tomography (CT). The reduction in the mechanical parameters of composites with 0.50 and 1.00 wt% CuO NPs may also be due to the slower hydration of the cement binder, as confirmed by changes in the heat of hydration for these configurations, or agglomeration of NPs, especially for the 1.00 wt% concentration, which was manifested in a decrease in the plasticity of the mortars.

Effect of Municipal Solid Waste Slag on the Durability of Cementitious Composites in Terms of Resistance to Freeze-Thaw Cycling.

The article presents durability results for cement mortars made with the addition of slag from municipal waste incineration plants as a replacement for natural aggregate. The undertaken durability tests included frost resistance tests and evaluation of strength, microstructure, water absorption and abrasiveness before and after 150 freeze-thaw cycles. The work reveals that MSWI slag in amounts up to 50 vol. % caused deterioration in the workability and water absorption of cement mortars, regardless of the type of cement used. This, in turn, resulted in a reduction in the compressive and flexural strengths of the composites compared to mortars made with sand alone. Nevertheless, the use of a higher grade of cement, CEM I 52.5 R, resulted in an increase in compressive strength and thus increased the mortars' frost and abrasion resistance. In addition, after the induced freeze-thaw cycles, mortars made with MSWI slag showed comparable or higher frost and abrasion resistance than those made using natural aggregate.

Research Development in Silica Aerogel Incorporated Cementitious Composites-A Review.

This paper presents an analysis of research results for silica aerogel cement composites over the past twenty years. Recently, two trends in the development of these composites have been noted, towards structural applications and towards ultralight composites for coatings and renders. Ongoing research shows that important aspects of cementitious composites with good mechanical performance are the proper selection of aggregates and improved adhesion at the silica aerogel-cement binder interface, which will guarantee high compressive strength with the lowest possible thermal conductivity. The best physicomechanical performance of aerogel cement composites with low thermal conductivity below 0.03 W/(m·K) was obtained when cenospheres and aerogel were used in a weight percentage of 5%. In turn, the prerequisites for using aerogel cement composites as coatings for energy-efficient building façades are the use of large amounts of silica aerogel as a substitute for lightweight aggregates or the selection of an optimal composition of lightweight aggregates and aerogel, ensuring the lowest possible thermal conductivity coefficient. Other important standpoints are water transport and moisture protection of the silica aerogel-based coatings. Therefore, in recent years, more and more elements of the hygrothermal performance, porosity and durability of silica aerogel cement composites have been developed. The article also points out the weaknesses of the application of silica aerogel in the cement matrix, the most important of which are the lack of adhesion at the boundary of the aerogel-cement binder, the increased porosity of the composite, the high water absorption capacity and the significant decrease in compressive strength with large volumes of silica aerogel. Solving these issues will certainly contribute to the wider applicability of these materials in the construction industry.

Long-Term Behavior of Cement Mortars Based on Municipal Solid Waste Slag and Natural Zeolite-A Comprehensive Physico-Mechanical, Structural and Chemical Assessment.

Limitations in natural aggregate resources and the continuous increase in the demand for concrete as a building material, as well as the increase in the production of waste and the problem with its storage were the reasons for attempts to replace the sand fraction in cement matrices with a corresponding slag fraction. Municipal solid waste incineration (MSWI) slag, which is a product of waste incineration, can be used as an aggregate. This extends its service life and reduces landfill waste. Therefore, three types of cement mortars with different aggregate composition were prepared. In addition, to increase the durability of the cement matrix and the degree of immobilization of harmful heavy metals and salts present in the slag, a natural zeolite with pozzolanic properties was used. A set of tests was carried out on fresh mortar and hardened mortar, including strength tests after 7, 28 and 360 days. What is more, chemical tests were undertaken, including the content of chlorides and sulfates, leaching using the TCLP method and oxide composition. The conducted tests revealed that all mortars had similar strength properties and demonstrated the effectiveness of immobilizing harmful substances contained in the municipal solid waste incineration (MSWI) slag by cementing.

The In Situ Hydrothermal and Microwave Syntheses of Zinc Oxides for Functional Cement Composites.

This study presents the results of research on cement mortars amended with two zinc oxides obtained by two different methods: hydrothermal ZnO-H and microwave ZnO-M. Our work indicates that, in contrast to spherical ZnO-H, ZnO-M was characterized by a columnar particle habit with a BET surface area of 8 m2/g, which was four times higher than that obtained for hydrothermally obtained zinc oxide. In addition, ZnO-M induced much better antimicrobial resistance, which was also reported in cement mortar with this oxide. Both zinc oxides showed very good photocatalytic properties, as demonstrated by the 4-chlorophenol degradation test. The reaction efficiency was high, reaching the level of 90%. However, zinc oxides significantly delayed the cement binder setting: ZnO-H by 430 min and ZnO-M by 380 min. This in turn affected the increments in compressive strength of the produced mortars. No significant change in compressive strength was observed on the first day of setting, while significant changes in the strengths of mortars with both zinc oxides were observed later after 7 and 28 days of hardening. As of these times, the compressive strengths were about 13-15.5% and 12-13% higher than the corresponding values for the reference mortar, respectively, for ZnO-H and ZnO-M. There were no significant changes in plasticity and flexural strength of mortars amended with both zinc oxides.

Physicomechanical and Antimicrobial Characteristics of Cement Composites with Selected Nano-Sized Oxides and Binary Oxide Systems.

In recent years, increasing attention has been paid to the durability of building materials, including those based on cementitious binders. Important aspects of durability include the increase of the strength of the cement matrix and enhancement of material resistance to external factors. The use of nanoadditives may be a way to meet these expectations. In the present study, zinc, titanium and copper oxides, used in single and binary systems (to better the effect of their performance), were applied as additives in cement mortars. In the first part of this work, an extensive physicochemical analysis of oxides was carried out, and in the second, their application ranges in cement mortars were determined. The subsequent analyses were employed in determining the physicochemical properties of pristine oxides: Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray fluorescence (EDXRF), scanning electron microscopy (SEM), measurement of the particle size distribution, as well as zeta potential measurement depending on the pH values. Influence on selected physicomechanical parameters of the cement matrix and resistance to the action of selected Gram-positive and Gram-negative bacteria and fungi were also examined. Our work indicated that all nanoadditives worsened the mechanical parameters of mortars during the first 3 days of hardening, while after 28 days, an improvement was achieved for zinc and titanium(IV) oxides. Binary systems and copper(II) oxide deteriorated in strength parameters throughout the test period. In contrast, copper(II) oxide showed the best antibacterial activity among all the tested oxide systems. Based on the inhibitory effect of the studied compounds, the following order of microbial susceptibility to inhibition of growth on cement mortars was established (from the most susceptible, to the most resistant): E. coli < S. aureus < C. albicans < B. cereus = P. aeruginosa < P. putida.

Carbon Fiber-Silica Aerogel Composite with Enhanced Structural and Mechanical Properties Based on Water Glass and Ambient Pressure Drying.

The article presents the synthesis of silica aerogel from a much cheaper precursor of water glass that was reinforced with short pitch carbon fiber by way of ambient pressure drying. Before being added to the silica gel, the carbon fibers were surface modified to increase adhesion at the interfacial border. We were able to obtain stable structures of the composite with the amount of fibers above 10% by volume. The presence of fibers in the silica matrix resulted in lower synthesis time of the composite, improved adhesion of fibers to the aerogel nanostructure, and increased mechanical and structural parameters. An additional effect of the presence of fibers in excess of 10% by volume was a new function of the nanocomposite-the ability to conduct electric current. The most optimal parameters of the composite, however, were obtained for silica aerogel reinforced with 10 vol.% of carbon fibers. This material indicated relatively low density and good physical parameters. The paper also analyzes the results on the synthesis of fiber-reinforced silica aerogels that have appeared in recent years and compares these to the results gained in presented work.

Biopolymer-Based Hybrids as Effective Admixtures for Cement Composites.

In the framework of this publication, silica-lignin hybrid materials were designed, obtained, characterized and then used as admixtures for cement composites. High-energy mechanical grinding of individual components was used to produce the systems that allowed ensuring adequate homogeneity of the final products. As a result of the analysis of Fourier transform infrared spectroscopy, it has been confirmed that weak physical interactions occur between the components. This allowed classifying the resulting systems as I class hybrid materials. In addition, the efficiency of obtaining final products was also inferred on the basis of obtained porous structure parameters and colorimetric data. The achieved bio-admixture with different weight ratios of silica and lignin was added to cement pastes in the amount ranging from 0.5 to 1 wt.%. The study showed that increasing the ratio of lignin in the admixture from 0.15 to 1 wt.% had a positive effect on the rheological properties of the pastes, while the mechanical properties of the composite were deteriorated. In turn, a higher amount of silica in the admixture acted in reverse. The most favorable results were obtained for a silica-lignin bio-admixture with a weight ratio of components equal to 5:1 wt./wt. A significant increase in compressive strength was gained at satisfactory plasticity of the paste.

Carbon Fiber and Nickel Coated Carbon Fiber-Silica Aerogel Nanocomposite as Low-Frequency Microwave Absorbing Materials.

Silica aerogel-based materials exhibit a great potential for application in many industrial applications due to their unique porous structure. In the framework of this study, carbon fiber and nickel coated carbon fiber-silica aerogel nanocomposites were proposed as effective electromagnetic shielding material. Herein, the initial oxidation of the surface of carbon fibers allowed the deposition of a durable Ni metallic nanolayer. The fibers prepared in this way were then introduced into a silica aerogel structure, which resulted in obtaining two nanocomposites that differed in terms of fiber volume content (10% and 15%). In addition, analogous systems containing fibers without a metallic nanolayer were studied. The conducted research indicated that carbon fibers with a Ni nanolayer present in the silica aerogel structure negatively affected the structural properties of the composite, but were characterized by two-times higher electrical conductivity of the composite. This was because the nickel nanolayer effectively blocked the binding of the fiber surface to the silica skeleton, which resulted in an increase of the density of the composite and a reduction in the specific surface area. The thermal stability of the material also deteriorated. Nevertheless, a very high electromagnetic radiation absorption capacity between 40 and 56 dB in the frequency range from 8 to 18 GHz was obtained.

Lignin-Based Hybrid Admixtures and their Role in Cement Composite Fabrication.

In this study, a technology for obtaining functional inorganic-organic hybrid materials was designed using waste polymers of natural origin, i.e., kraft lignin and magnesium lignosulfonate, and alumina as an inorganic component. Al2O3-lignin and Al2O3-lignosulfonate systems were prepared by a mechanical method using a mortar grinder and a planetary ball mill, which made it possible to obtain products of adequate homogeneity in an efficient manner. This was confirmed by the use of Fourier transform infrared spectroscopy and thermogravimetric analysis. In the next step, the developed hybrid materials were used as functional admixtures in cement mixtures, thus contributing to the formation of a modern, sustainable building material. How the original components and hybrid materials affected the mechanical properties of the resulting mortars was investigated. The admixture of biopolymers, especially lignin, led to cement composites characterized by greater plasticity, while alumina improved their strength properties. It was confirmed that the system containing 0.5 wt.% of alumina-lignin material is the most suitable for application as a cement mortar admixture.

Recent Advances in Research on the Synthetic Fiber Based Silica Aerogel Nanocomposites.

The presented paper contains a brief review on the synthesis and characterization of silica aerogels and its nanocomposites with nanofibers and fibers based on a literature study over the past twenty years and my own research. Particular attention is focused on carbon fiber-based silica aerogel nanocomposites. Silica aerogel is brittle in nature, therefore, it is necessary to improve this drawback, e.g., by polymer modification or fiber additives. Nevertheless, there are very few articles in the literature devoted to the synthesis of silica aerogel/fiber nanocomposites, especially those focusing on carbon fibers and nanofibers. Carbon fibers are very interesting materials, namely due to their special properties: high conductivity, high mechanical properties in relation to very low bulk densities, high thermal stability, and chemical resistance in the silica aerogel matrix, which can help enhance silica aerogel applications in the future.